Meshtastic network support
Complete Meshtastic network support.
ESP32S3 + SX1262 +GPS LoRa Node, Meshtastic and LoRaWAN Compatible (Phaseout item, not recommended for new design)
Wireless Tracker is a development kit based on ESP32-S3FN8. It integrates both SX1262 and UC6580 to provide fast GNSS solution for IoT. It can track any object and then upload that data wirelessly by Wi-Fi, Bluetooth, LoRa, and has been widely used in Meshtastic.
Wireless Tracker supports GPS, GLONASS, BDS, Galileo, NAVIC, QZSS multi-system joint positioning. It is perfectly compatible with Arduino, can be widely used in development such as bicycle sharing services, tracking pets or livestock, locating vehicles, tracking children, etc.
Current product
Wireless Tracker [Phaseout]
Wireless Tracker is a development kit based on ESP32-S3FN8. It integrates both SX1262 and UC6580 to provide fast GNSS solution for IoT. It can track any object and then upload that data wirelessly by Wi-Fi, Bluetooth, LoRa, and has been widely used in Meshtastic.
Wireless Tracker supports GPS, GLONASS, BDS, Galileo, NAVIC, QZSS multi-system joint positioning. It is perfectly compatible with Arduino, can be widely used in development such as bicycle sharing services, tracking pets or livestock, locating vehicles, tracking children, etc.
![]()
| Parameters | Description |
|---|---|
| Master Chip | ESP32-S3FN8 (Xtensa®32-bit lx7 dual core processor) |
| LoRa Chipset | SX1262 |
| GNSS Chipset | UC6580 |
| Frequency | 470 ~ 510MHz , 863 ~ 928MHz |
| Max. TX Power | 21±1dBm |
| Max. Receiving Sensitivity | -134dBm |
| Wi-Fi | 802.11 b/g/n, up to 150Mbps |
| Bluetooth LE | Bluetooth 5, Bluetooth mesh |
| Hardware Resource | 7 * ADC1 + 2 * ADC2; 7 * Touch; · 3 * UART; · 2 * I2C; 2 * SPI; etc. |
| Interface | Type-C USB; · 1.25mm-2P lithium battery interface; · LoRa ANT(IPEX1.0); · GNSS ANT(IPEX1.0); · Two sets of 18-pin, 2.54mm pitch pin headers |
| Battery | 3.7V lithium battery power supply and charging |
| Operating Temperature | -20 ~ 70 ℃ |
| Dimensions | 65.48 * 28.06 * 13.52mm |

The default packing list without selecting any accessories is as follows:
| Item | Quantity |
|---|---|
| Wireless Tracker | x1 |
| LoRa Antenna | x1 |
| SH1.25×2 Battery Connector | x1 |
| Pin Header | x2 |
Check if the USB cable supports data transfer by verifying if the connected cell phone supports file transfer.
Connect the USB cable, press and hold the ‘USER’ key, then press the ‘RST’ key once. Finally, release the ‘USER’ key to initiate the code download.
Connect the serial port and check whether the node is activated. If the node is not activated, refer to this link to activate it: https://docs.heltec.org/general/how_to_use_license.html.
Imagine that you want to measure the moisture in your field. Although, it is not far from your house, it probably doesn’t have Wi-Fi coverage. So, you can build a sensor node with an ESP32 and a moisture sensor, that sends the moisture readings once or twice a day to another ESP32 using LoRa.The later ESP32 has access to Wi-Fi, and it can run a web server that displays the moisture readings.This is just an example that illustrates how you can use the LoRa technology in your ESP32 projects.
Please refer to this document:
This issue had been well solved in the last update. The firmware will automatically recognize the device version and operation it.
The resistor at the arrow position is connected to the onboard antenna by default. After rotating it 90 degrees and soldering it to the position in the red box, the onboard antenna will be disconnected and the connection will switch to the IPEX interface.
You can directly use a 0-ohm resistor to short-circuit the boxed position, but in this case, both the onboard antenna and the IPEX interface will be enabled simultaneously, which may affect the signal.
Customer reviews for this product will appear here when available.
Markdown is supported. Switch between editing and previewing your message.
Wireless Tracker is a development kit based on ESP32-S3FN8. It integrates both SX1262 and UC6580 to provide fast GNSS solution for IoT. It can track any object and then upload that data wirelessly by Wi-Fi, Bluetooth, LoRa, and has been widely used in Meshtastic.
Wireless Tracker supports GPS, GLONASS, BDS, Galileo, NAVIC, QZSS multi-system joint positioning. It is perfectly compatible with Arduino, can be widely used in development such as bicycle sharing services, tracking pets or livestock, locating vehicles, tracking children, etc.
![]()
| Parameters | Description |
|---|---|
| Master Chip | ESP32-S3FN8 (Xtensa®32-bit lx7 dual core processor) |
| LoRa Chipset | SX1262 |
| GNSS Chipset | UC6580 |
| Frequency | 470 ~ 510MHz , 863 ~ 928MHz |
| Max. TX Power | 21±1dBm |
| Max. Receiving Sensitivity | -134dBm |
| Wi-Fi | 802.11 b/g/n, up to 150Mbps |
| Bluetooth LE | Bluetooth 5, Bluetooth mesh |
| Hardware Resource | 7 * ADC1 + 2 * ADC2; 7 * Touch; · 3 * UART; · 2 * I2C; 2 * SPI; etc. |
| Interface | Type-C USB; · 1.25mm-2P lithium battery interface; · LoRa ANT(IPEX1.0); · GNSS ANT(IPEX1.0); · Two sets of 18-pin, 2.54mm pitch pin headers |
| Battery | 3.7V lithium battery power supply and charging |
| Operating Temperature | -20 ~ 70 ℃ |
| Dimensions | 65.48 * 28.06 * 13.52mm |

The default packing list without selecting any accessories is as follows:
| Item | Quantity |
|---|---|
| Wireless Tracker | x1 |
| LoRa Antenna | x1 |
| SH1.25×2 Battery Connector | x1 |
| Pin Header | x2 |
Check if the USB cable supports data transfer by verifying if the connected cell phone supports file transfer.
Connect the USB cable, press and hold the ‘USER’ key, then press the ‘RST’ key once. Finally, release the ‘USER’ key to initiate the code download.
Connect the serial port and check whether the node is activated. If the node is not activated, refer to this link to activate it: https://docs.heltec.org/general/how_to_use_license.html.
Imagine that you want to measure the moisture in your field. Although, it is not far from your house, it probably doesn’t have Wi-Fi coverage. So, you can build a sensor node with an ESP32 and a moisture sensor, that sends the moisture readings once or twice a day to another ESP32 using LoRa.The later ESP32 has access to Wi-Fi, and it can run a web server that displays the moisture readings.This is just an example that illustrates how you can use the LoRa technology in your ESP32 projects.
Please refer to this document:
This issue had been well solved in the last update. The firmware will automatically recognize the device version and operation it.
The resistor at the arrow position is connected to the onboard antenna by default. After rotating it 90 degrees and soldering it to the position in the red box, the onboard antenna will be disconnected and the connection will switch to the IPEX interface.
You can directly use a 0-ohm resistor to short-circuit the boxed position, but in this case, both the onboard antenna and the IPEX interface will be enabled simultaneously, which may affect the signal.
Customer reviews for this product will appear here when available.
Markdown is supported. Switch between editing and previewing your message.

863~870 MHz, 902~928MHz SMA antenna
$3.90
IPEX (V1) - SMA converter cable, RF1.13
$0.90
SMA antenna and its corresponding IPEX-SMA adapter cable
$0.90