USB Type C
The power supply, firmware download, and debugging interfaces adopt a more universal USB Type C interface, making development work more convenient.
ESP32S3 + SX1262 LoRa Node development boad, LoRaWAN Compatible
In order to meet the user’s requirements for high performance and small size, we designed this product. On the basis of WiFi LoRa 32, it’s has a smaller size, 0.49″ OLED display, and better RF characteristics.

ESP32S3 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$14.90
ESP32S3R8 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$21.90
ESP32S3R8 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$17.90
nRF52840 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$17.90
ESP32-S3 +GPS+LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$30.90
nRF52840 +GPS+LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$33.90Current product
Wireless Stick(V3)
In order to meet the user’s requirements for high performance and small size, we designed this product. On the basis of WiFi LoRa 32, it’s has a smaller size, 0.49″ OLED display, and better RF characteristics.

| Parameters | Description |
|---|---|
| Master Chip | ESP32-S3FN8 (Xtensa®32-bit lx7 dual core processor) |
| LoRa Node Chip | SX1262 |
| USB to Serial Chip | CP2102 |
| Frequency | 433 ~ 510MHz, 863 ~ 928MHz |
| Max. TX Power | 21 ± 1 dBm |
| Max. Receiving Sensitivity | -134dBm |
| Wi-Fi | 802.11 b/g/n, up to 150Mbps |
| Bluetooth | Bluetooth LE: Bluetooth 5, Bluetooth mesh |
| Hardware Resource | 7 * ADC1 + 2 * ADC2; · 7 *T ouch; 3 * UART; 2 * I2C; · 2 * SPI; etc. |
| Display | 0.49-inch OLED |
| Memory | 384KB ROM; 512KB SRAM; · 16KB RTC SRAM; 8MB SPI Flash |
| Battery | 3.7V lithium battery power supply and charging |
| Operating temperature | -20 ~ 70 ℃ |
| Dimensions | 58.08 * 22.6* 8.2 mm |
| Interface | Type-C USB; · 21.25 lithium battery interface; · LoRa ANT(IPEX1.0); · 217*2.54 Header Pin |

The default packing list without selecting any accessories is as follows:
| Item | Quantity |
|---|---|
| Wireless Stick | x1 |
| Glue Rod Antenna | x1 |
| 1.25×2 Battery Connector | x1 |
| Pin Map Sticker | x1 |
If you want to use the new ESP32-S3 processor and the SX1262 LoRa chip, you may need to use new libraries that support them. You should check that the libraries you are using are compatible with these new components.
As far as my experience with the Wireless Stick Lite is concerned, the only library I had to change when switching from V1 to V3 was the LoRa library. The Sandeep Mistry LoRa library that I used earlier doesn’t work with the new SX1262 LoRa chip. To make my code work with the V3, I had to migrate to the Heltec LoRaWan_APP library. This was a true migration because the two libraries don’t use identical calls.
Due to the small screen of the board, it does not support Meshtastick’s screen display at present. You can download the firmware of the Wireless Stick Lite directly.
Imagine that you want to measure the moisture in your field. Although, it is not far from your house, it probably doesn’t have Wi-Fi coverage. So, you can build a sensor node with an ESP32 and a moisture sensor, that sends the moisture readings once or twice a day to another ESP32 using LoRa.The later ESP32 has access to Wi-Fi, and it can run a web server that displays the moisture readings.This is just an example that illustrates how you can use the LoRa technology in your ESP32 projects.
Customer reviews for this product will appear here when available.
Markdown is supported. Switch between editing and previewing your message.

ESP32S3 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$14.90
ESP32S3R8 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$21.90
ESP32S3R8 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$17.90
nRF52840 + SX1262 LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$17.90
ESP32-S3 +GPS+LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$30.90
nRF52840 +GPS+LoRa Node, Meshtastic, MeshCore and LoRaWAN Compatible
$33.90In order to meet the user’s requirements for high performance and small size, we designed this product. On the basis of WiFi LoRa 32, it’s has a smaller size, 0.49″ OLED display, and better RF characteristics.

| Parameters | Description |
|---|---|
| Master Chip | ESP32-S3FN8 (Xtensa®32-bit lx7 dual core processor) |
| LoRa Node Chip | SX1262 |
| USB to Serial Chip | CP2102 |
| Frequency | 433 ~ 510MHz, 863 ~ 928MHz |
| Max. TX Power | 21 ± 1 dBm |
| Max. Receiving Sensitivity | -134dBm |
| Wi-Fi | 802.11 b/g/n, up to 150Mbps |
| Bluetooth | Bluetooth LE: Bluetooth 5, Bluetooth mesh |
| Hardware Resource | 7 * ADC1 + 2 * ADC2; · 7 *T ouch; 3 * UART; 2 * I2C; · 2 * SPI; etc. |
| Display | 0.49-inch OLED |
| Memory | 384KB ROM; 512KB SRAM; · 16KB RTC SRAM; 8MB SPI Flash |
| Battery | 3.7V lithium battery power supply and charging |
| Operating temperature | -20 ~ 70 ℃ |
| Dimensions | 58.08 * 22.6* 8.2 mm |
| Interface | Type-C USB; · 21.25 lithium battery interface; · LoRa ANT(IPEX1.0); · 217*2.54 Header Pin |

The default packing list without selecting any accessories is as follows:
| Item | Quantity |
|---|---|
| Wireless Stick | x1 |
| Glue Rod Antenna | x1 |
| 1.25×2 Battery Connector | x1 |
| Pin Map Sticker | x1 |
If you want to use the new ESP32-S3 processor and the SX1262 LoRa chip, you may need to use new libraries that support them. You should check that the libraries you are using are compatible with these new components.
As far as my experience with the Wireless Stick Lite is concerned, the only library I had to change when switching from V1 to V3 was the LoRa library. The Sandeep Mistry LoRa library that I used earlier doesn’t work with the new SX1262 LoRa chip. To make my code work with the V3, I had to migrate to the Heltec LoRaWan_APP library. This was a true migration because the two libraries don’t use identical calls.
Due to the small screen of the board, it does not support Meshtastick’s screen display at present. You can download the firmware of the Wireless Stick Lite directly.
Imagine that you want to measure the moisture in your field. Although, it is not far from your house, it probably doesn’t have Wi-Fi coverage. So, you can build a sensor node with an ESP32 and a moisture sensor, that sends the moisture readings once or twice a day to another ESP32 using LoRa.The later ESP32 has access to Wi-Fi, and it can run a web server that displays the moisture readings.This is just an example that illustrates how you can use the LoRa technology in your ESP32 projects.
Customer reviews for this product will appear here when available.
Markdown is supported. Switch between editing and previewing your message.

SMA antenna and its corresponding IPEX-SMA adapter cable
$0.90
863~870 MHz, 902~928MHz SMA antenna
$3.90
IPEX (V1) - SMA converter cable, RF1.13
$0.90
Waterproof Enclosure for Outdoor Meshtastic/MeshCore
$45.20